Milnor MWF18J8 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 35

Milnor MWF18J8 Скачать руководство пользователя страница 12

10

Pellerin Milnor Corporation

WARNING:

Confined Space Hazards —

Confinement in the cylinder can kill or injure

you. Hazards include but are not limited to panic, burns, poisoning, suffo-
cation, heat prostration, biological contamination, electrocution, and
crushing.

�

Do not enter the cylinder until it has been thoroughly purged, flushed,

drained, cooled, and immobilized.

BNWCAI02 / 2021225

BNWCAI02

0000204672

B.3

5/27/21 9:35 AM

Released

Installation Tag Guidelines

BNWCAI02.R01 0000204671 B.2 B.3 5/27/21 9:34 AM Released

MWF18J8

MWF18Z8

MWR12J5

MWR12X5

MWR36J4

MWT12E5

MWT16E5

MWT16J5

MWT16X5

MWT18E4

MWT18J6

MWT18X4

MWT27E5

MWT27J5

MWT27X5

NOTICE:

This information may apply to models in addition to those listed above. It

applies to paper tags. It does not apply to the vinyl or metal safety placards, which must
remain permanently affixed to the machine and replaced if no longer readable.

Paper tags on the machine provide installation guidelines and precautions. The tags can be tie-on
or adhesive. You can remove tie-on tags and white, adhesive tags after installation. Yellow adhe-
sive tags must remain on the machine.

The following entries explain the installation tags. Each entry includes: 1) the tag illustration, 2)
the tag part number at the bottom of the tag, and 3) the meaning of the tag.

Display or Action

Explanation

Read the manuals before proceeding. This symbol appears on
most tags. The machine ships with safety, operator, and routine
maintenance guides for customer use. Milnor dealer manuals for
installing, commissioning, and servicing the machine are also
available from the Milnor Parts department.

B2TAG88005: This carefully built product was tested and in-
spected to meet Milnor performance and quality standards by
(identification mark of tester).

B2TAG94081: Motor must rotate in this direction. On single mo-
tor washer-extractors and centrifugal extractors, the drive motor
must turn in this direction during draining and extraction. This tag
is usually wrapped around a motor housing. If the motor turns in
the opposite direction when the machine is first tested, the electri-
cal hookup is incorrect and must be reversed as explained in the
schematic manual.

General Information

«
...
10
11
12
13
14
...
»

Содержание MWF18J8




































Отзывы:

Нет отзывов