Milnor C4A Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 36

Milnor C4A Скачать руководство пользователя страница 11

CQVUdi V_b 3_Y^ ?`UbQdUT GQcXUb5hdbQSd_bc

@5<<5B9> =9<>?B 3?B@?B1D9?>

a. If the machine starts without coins at any time as power is turned ON, take the machine
out of service until the coin counter has been changed. Do not return the machine to
service until it successfully passes all seven steps described herein.

b. If the machine does not start without coins at any time power was turned ON and OFF 25
times, you probably have a good coin counter. Proceed to step 6.

Step 6. Insert the proper number of coins. Verify that:

• the machine starts only after the last coin is accepted, and

• the machine will then accept no more coins.

a. If the machine starts before the last coin is accepted or accepts more than the proper
number of coins, take the machine out of service until you determine and fix what is
wrong. Do not return the machine to service until it successfully passes all seven steps
described herein.

b. If the coin counter functions properly and the machine starts, wait a full 2.5 minutes, then
proceed to step 7.

20DC8>= ' ) BRP[S 7PiPaSb—Contact with hot bath liquor can scald you.
• During following step, hold the door firmly closed, as shown in Figure 3, to prevent door

from springing open if the latch retracts during this test.

Figure 3: Hold Door Shut When Testing the Door
Interlock

Step 7. After the machine has been running at least 2.5 minutes, and while manually holding the
door closed (Figure 3), attempt to depress the door unlock handle.

a. If the latch retracts, take the machine out of service until the problem is diagnosed and
fixed. Do not return the machine to service until it successfully passes all seven steps
described herein.

b. If the latch does not retract, it is OK to return the machine to service (provided it also
passes all other tests described herein).

=^cXRT ( ) 4]bdaT BPUT >_TaPcX^]—Confirm daily, the door interlock function. Confirm
monthly, both the coin counter and the door interlock function.

• To test only the locking-type door interlock (daily), perform Step 6 and 7.

• To test the electronic coin counter and the locking-type door interlock (monthly), perform

all of the following steps, in order. Do not skip any step.

— End of BIRMCS01 —

«
...
9
10
11
12
13
...
»

Содержание C4A





































Отзывы:

Нет отзывов