Milnor 68036M5K Скачать руководство пользователя страница 93

Страница: 93 / 185

Disk Brake Maintenance

PELLERIN MILNOR CORPORATION

2. Turn the "brake release" output on. The air valve will supply compressed air to one of the

tubes. (

Figure 1

, item 1).

3. Quickly move one of the compressed air tubes (

Figure 1

, item 1) on and off the air cylinder.

4. After you complete this procedure, connect the air tubing.

6.4.

How the Brake Operates on Divided Cylinder Machines

Figure 7: A Typical First and Second Brake on a Divided Cylinder Machine

Two pairs of air tubing connect to different ends of the air

cylinder.

Legend

Tubing for air that releases

the first brake ( 85 -100
PSI) ( 5.95 - 07.0 kg/cm-
cm)

Tubing for air that applies

the second brake (10 – 12
PSI) (0.7-0.84 kg/cm-cm)

• On divided cylinder machines, two pair of air tubes connect to different ends of the air

cylinder.

• When the cylinder turns, air pressure at

Figure 7

, item 1 compresses the spring and releases

the brake.

• When you operate the stop control, air pressure at 1 is removed. Then the spring in the air

cylinder applies the brake.

• If you open the door, the 2nd brake is applied. Then the air pressure at

Figure 7

, item 2 and

the spring apply the brake.

6.5.

The Second Brake

—If your machine has a second brake which uses air pressure and

spring pressure, it will have a pressure regulator. Make sure that you adjust the air pressure of the
second brake (

Figure 7

, item 2) to 10 – 12 PSI (0.7-0.84 kg/cm-cm).

— End of BIEUUM01 —

Содержание 68036M5K


























































































































































































Результаты поиска

Содержание 68036M5K

Отзывы:

Похожие инструкции для 68036M5K

Бренды по названию

Популярные бренды

Milnor 68036M5K, Установка и обслуживание

Результаты поиска

Содержание 68036M5K

Отзывы:

Похожие инструкции для 68036M5K

Бренды по названию

Популярные бренды