manualshive.com logo in svg

Milnor 68036M5K, Установка и обслуживание

Поделиться
Скачать
Milnor 68036M5K Скачать руководство пользователя страница 44

 

 

 

 

 

PELLERIN MILNOR CORPORATION

 

  

BIIFLI01 (Published)   Book specs-  Dates: 20140321 / 20140321 / 20140321  Lang: ENG01  Applic: IFL IHU 

 

  

48040F_, 48040H_ & 68036H_ Washer Extractor Installation 

 

1. 

 

Handling 

 

Note 1: 

Once the machine is given to the carrier for delivery, it is solely the responsibility of the carrier to 

ensure that no damage occurs during transit. In addition to readily apparent damage, carriers are liable for 
concealed damage. Do not hesitate to file a claim with the carrier if the machine is damaged in any way 
during shipment. Milnor will be glad to assist you in filing your claim, but is not responsible for any 
shipping damage to the machine once it has been delivered to the carrier in good condition. 

1.  Remove the protective coverings (leaving the machine on shipping skids) and examine 

carefully for possible shipping damage. If the machine is damaged, notify the transportation 
company immediately. 

2.  Locate the lift points as shown in 

Figure 1

. 

3.  Attach chains as shown in 

Figure 2

. 

Figure 1: Where To Lift 

 

Figure 2: Rigger liable for damages 

 

  

 

 

  

 

 

CAUTION  1 : Machine damage hazard

—Improper placement of pickup chains can cause 

direct or indirect damage to machine.  

•  Use a 4 point pickup (as shown in 

Figure 2

) 

•  Use long pickup chains to prevent racking and/or twisting machine frame  

 

2. 

 

Moving the Machine into Place 

 

1.  Use skids for fork lifting. If possible, leave the machine on shipping skids until it is near its 

final position. Once skids are removed, carefully place forks under base. Do not allow the 
forks to come in contact with valves, piping, motors, etc., located under the machine. Do not 
push or hit the shell front when uncrating or installing the machine as it may cause the door to 
leak. 

2.  Never push, pull, lift, jack, or exert pressure on any components that protrude from the 

machine frame (shell front, door, electric boxes, controls, guards, conduits, conveyors, 
piping, valves, drains, vents, tilt frames, etc.). 

3.  Do not pull on door conduit to help move the machine as the door switch may require 

readjustment. 

40

Содержание 68036M5K


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды