background image

OM-246 522 Page 20

SECTION 5 

 OPERATION

5-1. Controls For Diversion 165 Models

1

Material Switch

!

Do not use AC output in damp areas, if

movement is confined, or if there is

danger of falling. Use AC output ONLY

if required for the welding process, and

then use a remote control.

!

Do not change position of switch while

welding or while under load.

.

Unit is equipped with Fan-On-Demand

t

.

Fan only runs when output is on or cooling

is required.

Use switch to select DC for steel, stainless

steel, and chrome-moly, or AC for aluminum

applications.
2

Material Thickness/Amperage Control

Use control to select material thickness and

corresponding amperage.

When Material switch is in the DC position, use

the blue scale to select the appropriate materi-

al thickness and corresponding amperage

from the white scale. When Material switch is

in the AC position, use the gray scale to select

the appropriate material thickness and corre-

sponding amperage from the white scale.
AC parameters have been optimized and auto-

matically set as follows:

Preflow is preset at .4 seconds for DC or AC

Postflow is preset for one second for every

ten amps of output, with a minimum of eight

seconds for DC or AC.

Balance is 72% EN (electrode negative)

Frequency is 120 Hz

3

Power Switch

Use switch to turn unit On and Off.
4

Power On LED

Power is on when LED is lit. LED flashes when

input power is more than 

10% of 230 volts. No

output available when LED is flashing.
5

Output Indicator LED

Output is On when LED is lit. LED flashes

when unit is overheated (see Section 3-5).

LED stops flashing when unit has cooled.

805 163-A / 232 896

3

4

5

2

1

Содержание DIVERSION 165 And

















































Отзывы: