Miller Axcess E Dual Скачать руководство пользователя страница 47

Страница: 47 / 64

OM-248965 Page 43

Stuck Error

ERR

STUK

Indicates the welding wire is stuck to the workpiece at the end of a weld. May be caused by poor weld conditions. The

error may be cleared by cutting wire from workpiece, and pressing the Jog/Purge button.

Weld Wait Error

WELD

WAIT

Indicates unit was not ready for a weld sequence. Press Jog/Purge button to clear error.

Please Wait Error

PLS

WAIT

Indicates user interface board lost data communications. Press Jog/Purge button to clear error. If condition persists, con-

tact nearest Factory Authorized Service gent.

Low Wire Feed Speed Error

LOW

WFS

Indicates actual wire feed speed is lower than wire feed speed command. Check for obstructions in the wire feed system

or a faulty wire drive system. Press Jog/Purge button to clear error.

Robot Memory Error

ROBT

MEM

Indicates robot lost memory data. Press Jog/Purge button to clear error.

Unit Communication Error

UNIT

COMM

Indicates the data bus on the PCM board is not functioning properly. Press Jog/Purge button to clear error.

RMD Done Message

RMD

DONE

Indicates the RMD demo is completed. Pressing Jog/Purge button will change the screen to CYCL PWR on the display.

Turn unit power off and back on again.

Содержание Axcess E Dual

































































Результаты поиска

Содержание Axcess E Dual

Отзывы:

Похожие инструкции для Axcess E Dual

Бренды по названию

Популярные бренды

Miller Axcess E Dual, Руководство пользователя

Результаты поиска

Содержание Axcess E Dual

Отзывы:

Похожие инструкции для Axcess E Dual

Бренды по названию

Популярные бренды