Miller Electric Big 40 CAT Скачать руководство пользователя страница 67

Страница: 67 / 92

OM-4406 Page 61

Return To Table Of Contents

SECTION 12

−

GENERATOR POWER GUIDELINES

The views in this section are intended to be representative of all engine-driven

welding generators. Your unit may differ from those shown.

NOTE

12-1. Selecting Equipment

gen_pwr 11/02

−

Ref. ST-159 730 / ST-800 577

Generator Power Receptacles

−

Neutral Bonded To Frame

3-Prong Plug From Case

Grounded Equipment

2-Prong Plug From Double

Insulated Equipment

Do not use 2-prong plug un-

less equipment is double in-

sulated.

Be sure equipment

has this symbol

and/or wording.

12-2. Grounding Generator To Truck Or Trailer Frame

S-0854

Always ground generator

frame to vehicle frame to pre-

vent electric shock and static

electricity hazards.

Equipment Grounding

Terminal (On Front Panel)

Grounding Cable (Not

Supplied)

Metal Vehicle Frame

Connect cable from equipment

ground terminal to metal vehicle

frame. Use #10 AWG or larger

insulated copper wire.

If unit does not have GFCI re-

ceptacles, use GFCI-pro-

tected extension cord.

Electrically bond generator

frame to vehicle frame by

metal-to-metal contact.

GND/PE

Bed liners, shipping skids, and some running

gear insulate the welding generator from the ve-

hicle frame. Always connect a ground wire from

the generator equipment grounding terminal to

bare metal on the vehicle frame as shown.

Содержание Big 40 CAT





























































































Результаты поиска

Содержание Big 40 CAT

Отзывы:

Похожие инструкции для Big 40 CAT

Бренды по названию

Популярные бренды

Miller Electric Big 40 CAT, Руководство пользователя

Результаты поиска

Содержание Big 40 CAT

Отзывы:

Похожие инструкции для Big 40 CAT

Бренды по названию

Популярные бренды