Manual
LOGO 600SX
- ©Mikado Model Helicopters GmbH - Page 2
Index
OPERATING YOUR MODEL SAFELY
Operate the helicopter in spacious areas with no
people nearby.
!Warning: Do NOT operate the helicopter in the fol-
lowing places and situations (or else you risk severe
accidents):
• in places where children gather or people pass
through
• in residential areas and parks
• indoors and in limited space
• in windy weather or when there is any rain, snow,
fog or other precipitation
If you do not observe these instructions you may be
held reliable for personal injury or property damage!
Always check the R/C system prior to operating your
helicopter. When the R/C system batteries get weaker,
the operational range of the R/C system decreases.
Note that you may lose control of your model when
operating it under such conditions.
Keep in mind that other people around you might also
be operating a R/C model.
Never use a frequency which someone else is using
at the same time. Radio signals will be mixed and you
will lose control of your model.
If the model shows irregular behavior, bring the model
to a halt immediately. Turn off all power switches and
disconnect the batteries. Investigate the reason and
fi x the problem. Do not operate the model again as
long as the problem is not solved, as this may lead to
further trouble and unforeseen accidents.
! Warning: In order to prevent accidents and personal
injury, be sure to observe the following:
Before fl ying the helicopter, ensure that all screws are
tightened. A single loose screw may cause a major
accident.
Replace all broken or defective parts with new ones,
as damaged parts lead to crashes.
Never approach a spinning rotor. Keep at least 10 me-
ters/yards away from a spinning rotor blades.
Do not touch the motor immediately after use. It may
be hot enough to cause burns.
Perform all necessary maintenance.
PRIOR TO ADJUSTING AND OPERATING YOUR MO-
DEL, OBSERVE THE FOLLOWING
!Warning: Operate the helicopter only outdoors and
out of people’s reach as the main rotor operates at
high rpm!
! Warning: While adjusting, stand at least 10 meters/
yards away from the helicopter!
Novice R/C helicopter pilots should always seek advice
from experienced pilots to obtain hints with assem-
bly and for pre-fl ight adjustments. Note that a badly
assembled or insuffi ciently adjusted helicopter is a
safety hazard!
In the beginning, novice R/C helicopter pilots should
always be assisted by an experienced pilot and never
fl y alone!
Tools for Assembly & R/C Equipment
Safety Instructions
Safety Instructions . . . . . . . . . . . . . . . . . 2
Tools for Assembly & R/C Equipment . . . . . . . 2
1 Mainframe . . . . . . . . . . . . . . . . . . . . . 3
2 Tail Rotor . . . . . . . . . . . . . . . . . . . . . 4
3 Tail Boom . . . . . . . . . . . . . . . . . . . . . 5
4 Main Gear & Tail Boom Assembly . . . . . . . . 6
5 V-Bar Rotor Head . . . . . . . . . . . . . . . . . 7
6 Servo Installation . . . . . . . . . . . . . . . . . 8
7 Mounting the Motor . . . . . . . . . . . . . . . . 9
8 Canopy Mounting . . . . . . . . . . . . . . . . . 9
9 Radio and Battery . . . . . . . . . . . . . . . 10
10 Overview Chassis . . . . . . . . . . . . . . . 11
11 Overview Tail Rotor . . . . . . . . . . . . . . 12
12 Overview V-Bar Head . . . . . . . . . . . . . 13
Manual Mikado LOGO 600 SX
Note:
There is no bag 4 and 10. The bags are numbered 1 to 12, with the exception of 4 and 10.
Max. rotorhead rpm LOGO SX 600:
2100
Max. collective range:
+/- 12°
Max. Rotor blade size:
600 mm - 620 mm
Max. LiPo Akku size:
10S 5000 mAh
Max. LiPo Akku size:
12S 3300 mAh
LOGO 600 SX is not recommended for novices. This heli-
copter is a complex system. Basic knowledge of the func-
tion of a model helicopter is required to build and operate
the LOGO 600 SX.
Radio with Heli-Software
Motor + Speed Controller (check the Mika-
do webpages for recommended motors)
Alle shown products are examples. You may use different brands.
Scissors
Rubber Hammer
Screwdrivers
(plus and minus)
Hex Wrenches
1.5/2.0/2.5/3.0 mm
(.055/.079/.098/.118 in)
Ball
link
pliers
Threadlock
circlips
pliers
Grease
Pitch Gauge
V-Bar
Battery
Modellbau Lindinger GmbH e-Mail: [email protected] www.lindinger.at
