Miele W 6071 Скачать руководство пользователя страница 31

Страница: 31 / 44

Fault messages

Repairs should only be carried out by a

qualified and trained person in accord-
ance with local and national safety
regulations. Unauthorized repairs could
cause an injury or machine damage.

Faults that occur before or after the start of a
program flash in the display.

PROGRAMME 11

COTTONS

PROGRAMME STOP

THROUGH POWER CUT

Press "Start" to continue the program.

Once power is restored, press

"Start".

This fault message can also indicate: The
overload cut-out of the drive motors has over
heated. Allow the motor to cool down.

PROGRAMME 11

COTTONS

PROGRAMME STOP

WATER INLET FAULT

Open water stopcock and press Start button.

Open the water valve (stopcock) and
press

"Start".

PROGRAMME 11

COTTONS

PROGRAMME STOP

DRAIN FAULT

Check drain system and press Start button.

Check and clean the drain system and
press

"Start".

PROGRAMME 11

COTTONS

PROGRAMME STOP

HEATING SYSTEM FAULT

Short circuit on heat sensor 1.

Contact Technical Service.

PROGRAMME 11

COTTONS

PROGRAMME STOP

HEATING SYSTEM FAULT

Cut-out on heat sensor 1.

Contact Technical Service.

PROGRAMME 11

COTTONS

PROGRAMME STOP

HEATING SYSTEM FAULT

Contact Technical Service.

PROGRAMME 11

COTTONS

PROGRAMME STOP

DRIVE SYSTEM FAULT

Multiplug drive variants failure.

Contact Technical Service.

PROGRAMME 11

COTTONS

90 °C

Main wash

20 °C

Rinse 1

DRIVE SYSTEM FAULT

Contact Technical Service. if there is no
drum movement after this message.

PROGRAMME 11

COTTONS

PROGRAMME STOP

IMBALANCE SWITCH

Press the On-Off switch.

Press

"Power off" and

"Power on".

PROGRAMME 11

COTTONS

PROGRAMME STOP

PRESSURE MONITOR FAULT

Contact Technical Service.

PROGRAMME 11

COTTONS

PROGRAMME STOP

DISPENSING SYSTEM FAULT

Dispensing container 1 empty

Change the dispensing container.

Frequently asked questions

Содержание W 6071













































Результаты поиска

Содержание W 6071

Отзывы:

Бренды по названию

Популярные бренды

Miele W 6071, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание W 6071

Отзывы:

Бренды по названию

Популярные бренды