background image

Delay start

28

To select delay start

With delay start you can delay the start
of the programme by up to a maximum
of 24 hours.

However: 

delay start cannot be used

with the 

Warm air

 programme.

After selecting the programme touch
the 

 sensor.

 will flash

– Times of up to 



 are selected in



 minute stages and then in hour

stages up to 



.

– If you touch the sensor continuously,

the time will count up to 



.

– Touching the 



 sensor again when

 shows in the display will delete

the time selected.

To begin delay start

Press the 

Start/Stop

 button.

 will light up

– Delay start times of more than 



 will

count down in hours and then in
minutes until the start of the
programme.

– The drum will turn briefly every hour

until the start of the programme to
reduce creasing.

To change delay start after it
has started counting down

Press the 

Start/Stop 

button.

 will flash

Touch the 

 sensor to change the

time.

Press the 

Start/Stop

 button.

To add/remove laundry after
delay start has started
counting down

You can open the door to add/
remove laundry.

– All programme settings will be saved

 will flash

You can also change the drying level, if
required.

Press the 

Start/Stop

 button so that

the delay start time continues to
count down.

To cancel delay start

Switch the dryer off and then on
again.

Содержание TKB 550 WP









































































Отзывы: