Miele TCE 620 WP Скачать руководство пользователя страница 52

Страница: 52 / 76

What to do if ...

Problem

Cause and remedy

A programme does not
start

No obvious cause.



Connect the tumble dryer to the mains



Turn on the tumble dryer



Close the door



Check whether the mains fuse has tripped

Has there been a power cut? When power is restored
any previously running programme will restart
automatically.

Only the

Start/Stop

sensor is now flashing

10 minutes after the end of the programme, the

Start/

Stop

sensor will begin to flash and the display will go

out: energy saving. This is not an error but a normal
function.
The drum will turn at intervals in the anti-crease
phase.



Touch a sensor to switch on the indicators.

See the "Programmable functions", chapter, "



Control panel switch-off status" section.

The dryer switches off
at the end of the
programme

The dryer switches off automatically: energy saving.
This is not an error but a normal function.



To switch the dryer on, select a programme.

Tip: you can change this. See the "Programmable
functions", chapter, "



Dryer switch-off status"

section.

The interior drum
lighting does not come
on

The drum lighting will switch off automatically ...
... when the door is closed.
... after a few minutes when the door is open (to save
energy).
If the dryer is switched on, the drum lighting will
come on when the door is opened.

Содержание TCE 620 WP













































































Результаты поиска

Содержание TCE 620 WP

Отзывы:

Похожие инструкции для TCE 620 WP

Бренды по названию

Популярные бренды

Miele TCE 620 WP, Руководство по эксплуатации

Результаты поиска

Содержание TCE 620 WP

Отзывы:

Похожие инструкции для TCE 620 WP

Бренды по названию

Популярные бренды