Miele T 9446 C Скачать руководство пользователя страница 54

Страница: 54 / 56

Buzzer

The buzzer has two volumes.

Normal (Factory default)
The buzzer sounds at the end of a
programme.

Loud
The buzzer sounds at maximum volume
at the end of a programme.

A tick

will appear beside the option

to show that it has been set.

Keypad tone

An audible tone sounds each time a
button is pressed.

A tick

will appear beside the option

to show that it has been set.
Factory default: Off.

Contrast

Brightness

There are ten different display
contrast and display brightness
settings.

The bar chart shows you the setting.
Factory default: a medium setting.

Standby display

To save energy, the display goes out
after 10 minutes and the indicator
light for the

Start/Stop

button will start

flashing slowly.

There are two options:

Standby is activated:

– if a programme is not selected within

10 minutes of the machine being
switched on.

– 10 minutes after a programme has

started.

– 10 minutes after the end of a

programme.

Not in current prog.
(Factory default)

– Standby is activated if a programme

is not selected within 10 minutes of
the machine being switched on and
after the end of a programme.
(Standby is not activated after a
programme has started).

Pressing one of the buttons switches
the display back on again.

A tick

will appear beside the option

to show that it has been set.

Memory

The electronics will memorise the
drying level and any extra options
selected for the current drying
programme.

A tick

will appear beside the option

to show that it has been set.
Factory default: Off.

Settings menu

Содержание T 9446 C

























































Результаты поиска

Содержание T 9446 C

Отзывы:

Бренды по названию

Популярные бренды

Miele T 9446 C, Руководство по эксплуатации

Результаты поиска

Содержание T 9446 C

Отзывы:

Бренды по названию

Популярные бренды