Miele T 8685 C Скачать руководство пользователя страница 59

Страница: 59 / 68

Buzzer

A buzzer sounds (at intervals for a maximum of 1 hr) to let
you know the programme has finished.

Off

= The buzzer will always sound when there is a fault,

even if it has been switched off.

Normal = The buzzer sounds at the end of a programme.

Loud

= The buzzer sounds louder at the end of a

programme.

A tick

will appear beside the option to show that it has

been set.
The machine is delivered with the option: Normal, set as stan-
dard.

Keypad tones

An audible tone sounds when the

Start

button, a short cut

button or the multi-function selector is pressed.

A tick will appear beside the option to show that it has been
set.
The machine is delivered with the option: Off, set as standard.

Display contrast

There are ten different display contrast settings.

The bar chart shows you the setting. The factory default
setting is a medium setting.

Settings menu

Содержание T 8685 C





































































Результаты поиска

Содержание T 8685 C

Отзывы:

Похожие инструкции для T 8685 C

Бренды по названию

Популярные бренды

Miele T 8685 C, Руководство по эксплуатации

Результаты поиска

Содержание T 8685 C

Отзывы:

Похожие инструкции для T 8685 C

Бренды по названию

Популярные бренды