Miele T 8685 C Скачать руководство пользователя страница 38

Страница: 38 / 68

Problem

Possible cause

Remedy

The following
message appears
after the
programme has
finished:

Clean out airways

The dryer is not working
efficiently or
economically.

Possible cause: The fluff
filters are clogged with
fluff or with detergent
residues.

–

Cleaning the filters is usually
all that is required.
However, if the message
does not go out after you
have cleaned the filters, then
also check all the possible
causes described under "The
drying process goes on too
long or even switches off".

To delete the fault message:

–

Switch the dryer off and then
back on again.

You can adjust the setting which
controls when or if the message

Clean out airways

appears.

See "Settings menu

, Airways

indicator".

Technical fault

– the programme

is cancelled

– the buzzer

sounds

No obvious cause.

In some circumstances,

Clean out airways

has

already been displayed.

–

Clean the filters and the
condenser unit.

To delete the fault message:

–

Switch the dryer off and then
back on again.

There is a fault if, despite
doing this, the
programme is cancelled
and the fault message
appears again.

Contact the Miele Service
Department.

Programme finish
time changed

This is not a fault.

Settings were changed while the
timer was counting down to the
start of a programme, or there
was a power cut.

Problem solving guide

Содержание T 8685 C





































































Результаты поиска

Содержание T 8685 C

Отзывы:

Похожие инструкции для T 8685 C

Бренды по названию

Популярные бренды

Miele T 8685 C, Руководство по эксплуатации

Результаты поиска

Содержание T 8685 C

Отзывы:

Похожие инструкции для T 8685 C

Бренды по названию

Популярные бренды