Miele T 4453 C Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 52

background image

If the appliance is supplied from a
cord extension set or electrical

portable outlet device the cord
extension set or electrical portable
outlet device should be positioned so it
is not subject to splashing or ingress of
moisture.

If the connection cable is faulty it
must only be replaced by a Miele

approved service technician to protect
the user from danger.

In the event of a fault or for
cleaning purposes, the machine is

only completely isolated from the
electricity supply when:

– it is switched off at the wall socket

and the plug is withdrawn, or

– it is switched off at the mains, or

– the mains plug is withdrawn.

Operation

This equipment is not designed for
maritime use or for use in mobile

installations such as caravans, aircraft
etc. However it may be suitable for
such usage subject to a risk
assessment of the installation being
carried out by a suitably qualified
engineer.

The dryer must not be used without
the fluff filters in place or if the fluff

filters are damaged in any way.

The dryer must not be used without
the condenser unit in place.

Do not install the machine in a
room where the temperature may

drop down to or below freezing. At very
cold temperatures the machine may be

difficult to start.
There is a risk of damage if the
condensed water is allowed to freeze in
the pump, hoses and / or condensed
water container.

If the water is drained externally
through the drain hose instead of

being collected in the condensed water
container, make sure the drain hose is
securely attached if you hang it in a
sink or basin to avoid the hose slipping
and the water causing damage.

Condensed water is not drinking
water. It can cause health

problems in both people and animals.

Always keep the area around the
machine free of dust and fluff.

Warning and Safety instructions

7

«
...
5
6
7
8
9
...
»

Содержание T 4453 C





















































Отзывы:

Нет отзывов

Похожие инструкции для T 4453 C

Бренд: Magic Страницы: 20

Бренд: T-Fal Страницы: 17

Бренд: T3 Страницы: 27

Бренд: Heinner Страницы: 52

Бренд: Smeg Страницы: 31

Бренд: GE Страницы: 144

Бренд: Franke Страницы: 4

Бренд: TORLEN PROFESSIONAL Страницы: 2

Бренд: GE Страницы: 7

Бренд: GE Страницы: 5

Бренд: GE Страницы: 16

Бренд: GE Страницы: 8

Бренд: GE Страницы: 4

Бренд: GE Страницы: 8

Бренд: GE Страницы: 16

Бренд: GE Страницы: 20

Бренд: GE Страницы: 33

Бренд: GE Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды