Miele PWM 507 Скачать руководство пользователя страница 57

Страница: 57 / 80

Installation

*INSTALLATION*

Installation locations

Side view

1132

850

1100

714

Washer-dryer stack

min. 300

1702

This washing machine can be installed
with a Miele tumble dryer on top of it. A
stacking kit (APCL001, optional
accessory) is required for this.

Installation on a raised plinth

The washing machine can be installed
on a steel plinth (open or closed,
available as an optional Miele
accessory) or on a concrete plinth.



Injury can occur if the washing

machine has not been adequately
secured.
When installed on a plinth, there is a
risk that the washing machine will
move and fall from the plinth during
spinning.
Secure the washing machine using
the clamps supplied.

Installation notes

This washing machine is not suitable
for building under.



Risk of damage due to moisture

ingress.
Moisture can damage electrical
components.
Do not install the machine near or
directly above an open gully or floor
drain.

Содержание PWM 507

















































































Результаты поиска

Содержание PWM 507

Отзывы:

Похожие инструкции для PWM 507

Бренды по названию

Популярные бренды

Miele PWM 507, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PWM 507

Отзывы:

Похожие инструкции для PWM 507

Бренды по названию

Популярные бренды