Miele PW 6055 Скачать руководство пользователя страница 63

Страница: 63 / 72

Pre-wash water

You can choose for the pre-wash to
be carried out with either hot or cold
water (not available with the

Curtains

programme). Hot water can only be
only taken in if the wash temperature
is above 30°C.

The machine is delivered with the

Hot

water option selected.

Main wash water

You can choose for the main wash to
be carried out with either hot or cold
water (not available with the

Woollens

Curtains

and

Proofing

programmes). Hot water can only be
only taken in if the wash temperature
is above 30°C.

The machine is delivered with the

Hot

water option selected.

If the machine is not connected to
the hot water supply, the programme
durations will be longer and will vary
from the time remaining shown in the
display.

The machine will need to be set up
specifically for

Recycled water

if this

option is selected.

Rinse water

You can choose for the rinses in the

Cottons hygiene

Cottons Uni.

Minimum iron

Kitchen linen

and

Sluice

programmes to be carried out

with either hot or cold water. Hot
water can only be only taken in if the
wash temperature is above 50°C.

The machine is delivered with the

Hot

water option selected.

The machine will need to be set up
specifically for

Recycled water

if this

option is selected.

Low water pressure

This setting can be activated to
ensure problem free water intake
where the water pressure is
constantly low (below 100 kPa).

The machine is delivered with the
option deactivated.

Settings/Supervisor level menu

Содержание PW 6055









































































Результаты поиска

Содержание PW 6055

Отзывы:

Похожие инструкции для PW 6055

Бренды по названию

Популярные бренды

Miele PW 6055, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PW 6055

Отзывы:

Похожие инструкции для PW 6055

Бренды по названию

Популярные бренды