Miele PW 6055 AV, План установки

Страница: 15 / 15

PW 6055/6065 en -
10 145 220 / 01 15
3. Drain into a floor drain (gully).
Permanent connection of the drain hose to a sink syphon
You may permanently connect the drain hose to a special sink
syphon.
If necessary, the hose may be extended to a maximum length of 5 m.
Accessories are available from an authorized Miele dealer or Miele
Technical Service.
For delivery heads over
3‘ 3 3/8“ (1 m) (up to a max. of 5‘ 10 7/8“ /
1.8 m), contact your Miele dealer or Miele Customer Service for a
drain pump.
Equipotential bonding
Depending on the local and national installation regulations, you may
have to create equipotential bonding with proper contact connection.
The connection material for a necessary equipotential bonding can be
ordered as an assembly kit from Miele Service or supplied by the user.
Peak load/energy management
Using an optional kit, you may connect the appliance to a peak load or
energy management system.
The appliance provides 3 signal contacts with mains potential and a
neutral conductor on terminal strip, which is identified with a, b, c, and
d.
a - Output signal: machine operation starts
b - Output signal: machine requests heating
c - Input signal peak load: machine switches heater
d
– Neutral conductor
When the peak load function is activated, the heating is switched off
and the program is stopped. The display returns a corresponding
message.
Upon the end of the peak load function, the program automatically
resumes.
Liquid dosing connection
You can use external liquid dosing pumps with low-level sensor for the
dosing of liquid detergents.
You can only use dosing pumps with internal controller and/or
programming option for liquid dosing.
Always note the manufacturers' instructions when using and
combining detergents and special products.
Payment device
The washing machine can be fitted with a single payment device as
an optional accessory. Only an authorized Miele dealer or the Miele
Service may program the appliance for this function.
Alternatively, you can use a wireless multi-station system for
maximum 8 terminals with a debit card payment device and additional
controllers for terminal monitoring.
Serial interface
The serial interface is provided with an additional integrated XKM
RS323 module.
The data interface leading from the XKM RS232 module is compliant
with SELV (safety extra-low voltage). Any connected external devices
must also comply with SELV.
The pluggable module is supplied with a connecting cable and a D-
sub plug for further connection.
Installation and fastening
The machine must be installed on a level, horizontal, and solid surface
which is capable of withstanding the specified stresses.
The floor load caused by the appliance affects the installation surface
as point load in the area of the device mounts.
Positional stability of the appliance is mandatory.
Use the adjustable mounts to horizontally align the appliance length-
and crosswise.
Use the supplied mounting bracket to attach the two front mounts of
the appliance to the floor. The fixing material is designed for a dowel
attachment to concrete flooring.
The user must provide fixing material for any different flooring design.
Platform installation
The washing machine may be installed on a base (open or closed
compartment) which may be optionally purchased from Miele. It may
also be installed on a user-supplied concrete platform.
The quality of the concrete and its strength must be assessed
according to the machine load. Ensure that the on-site concrete
platform has an adequate grip on the substrate.
If the washing machine is installed on a user-supplied platform
(concrete or masonry), you must secure the machine with the
mounting bracket to prevent the possibility of the washing machine
toppling off the platform during the spin cycles.
Washer/dryer stack
The Miele washing machine can be installed in combination with a
Miele dryer as part of a washer-dryer stack. For this purpose, you
require a connection kit
(WTV) which can be optionally purchased.
Only an authorized specialist or Miele Service representative may
install the connection kit.