Miele PT 7136 Plus Скачать руководство пользователя страница 8

Страница: 8 / 60

Menu Program selection

Programme

selection

Back

Cottons

Minimum iron
Woollens handcare

All pre-set programs can be selected with the jog shuttle.
Depending on the direction the jog shuttle is turned the
highlighter moves up or down.

The arrows

at the right side of the display show that more

selections are available.

Press the jog shuttle to open the basic menu of the
selected program.

Basic menu of a drying program

Cottons

Normal

Duration 1:16 h

Low temp.

Timer

Save

Back

The "Drying level" or "Program" can be selected by turning
the jog shuttle.

– The selected component is highlighted. Press the jog

shuttle to select or adjust the component.

– Select "Low temp." or "Timer" by pressing

– Press

to get back to the Basic menu.

All components can also be selected and confirmed with the
jog shuttle only.

Settings

The "Settings

" menu allows you to adjust the dryer to

individual needs. See "Settings

" for more information.

Guide to the dryer

Содержание PT 7136 Plus




























































Результаты поиска

Содержание PT 7136 Plus

Отзывы:

Похожие инструкции для PT 7136 Plus

Бренды по названию

Популярные бренды

Miele PT 7136 Plus, Руководство пользователя

Результаты поиска

Содержание PT 7136 Plus

Отзывы:

Похожие инструкции для PT 7136 Plus

Бренды по названию

Популярные бренды