Miele PT 7136 Plus Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 60

background image

Cleaning the lint filter

,

Check and clean the lint filter

when the following message shows:
"Clean the filters" or "Clean out
airways".

A two-piece lint filter in the dryer fan
cavity collects the lint. It has to be
removed and disassembled.

Note: Use a vacuum cleaner to clean
the lint filter without touching it.

Removing the lint filter

^

Press on the right side of the flap to
open it.

^

Pull the lint filter out by its handle.

Disassembling the lint filter

^

Hold the lint filter with both handles
and twist the inner filter towards you,
then pull apart (see illustration).

Cleaning and Care

22

«
...
20
21
22
23
24
...
»

Содержание PT 7136 Plus





























































Отзывы:

Нет отзывов

Похожие инструкции для PT 7136 Plus

Бренд: Haier Страницы: 10

Бренд: Haier Страницы: 7

Бренд: Danby Страницы: 4

Бренд: Ayce Страницы: 36

NovaWheel NWB- DC+ Series

Бренд: NovaTec Страницы: 32

ARTIST BREEZE 1800W

Бренд: OBH Nordica Страницы: 24

Бренд: Morphy Richards Страницы: 6

Бренд: Amana Страницы: 7

Бренд: GE Страницы: 32

Бренд: GE Страницы: 40

Бренд: GE Страницы: 128

Бренд: GE Страницы: 16

Бренд: TORLEN PROFESSIONAL Страницы: 2

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 20

Бренд: SEVERIN Страницы: 1

Бренд: CDA Страницы: 20

Бренд: Fisher & Paykel Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды