manualshive.com logo in svg

Miele PG 8581, Руководство по эксплуатации

Поделиться
Скачать
Miele PG 8581 Скачать руководство пользователя страница 118

Frequently asked questions

118

Process-related faults and messages

Problem

Possible cause and solution

Drying during program deacti-
vated

Drying cannot be selected at the start of a program be-
cause drying is not available for the selected program.

Start the program without drying.

Or

Have the drying parameters for this program adjusted by
Miele Service.

Wrong code entered

The PIN code entered is not the same as the code saved.

Enter the PIN code again.

Report the loss of the PIN code to Miele Service.

Test program: Test object
can now be removed

This is not a fault.
A test program is running to check performance. At certain
points in the program, the sequence is interrupted so that
samples can be taken.

Take a sample.

or

Wait. The program will continue automatically in approx.
30 seconds.

or

Continue the program without delay by pressing the

Start/Stop

 button.

Program cancelled

This is not a fault.
A program which was running was canceled by the user.

The wash cabinet interior can be very hot.

When the door is opened, hot steam and process chemi-
cals can escape. Protective measures for personal safety
must be observed.

Program continued

This is not a fault.
The process of canceling a program was not completed.

The program which was running continued without inter-
ruption.

Peak load cut-out

This is not a fault! 
Individual components of the machine are paused while
there is a peak load signal from your energy management
system.

All settings reset

This is not a fault.
A user has restored factory default settings.

Confirm the message with 

OK

.

All program settings reset

This is not a fault! 
A user has restored the factory default setting for the pro-
gram.

Confirm the message with 

OK

.

Содержание PG 8581

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды