Miele NOVOTRONIC W 1612 Скачать руководство пользователя страница 35

Страница: 35 / 60

Fault messages in the display

Problem

Possible cause

Remedy

The display lights up

;

and

Drain fault

flashes.

– The water outlet is

restricted or
blocked.

– The drain hose is

sitting too high.

– Clean the drain filter and

pump.

– The max. drain pump

height (delivery head) is
1m.

The display lights up

;

and

Water inlet fault

flashes.

The water inlet is
blocked or restricted.

Check whether:

– the stopcock is open

enough.

– the inlet hose is pinched or

bent.

– the water pressure is too

low.

The display lights up

;

and

Waterproof fault

flashes.

The water protection
system was triggered.

Call the service department.

The display lights up

;

and

Technical fault

flashes.

There is a fault.

Re-start the program.
If the fault message appears
again, call Customer Service.

The display flashes

Anti-crease
Chk detergent

Excessive foam has
built up during
washing.

Use less detergent next time,
and check the recommended
doses on the package.

To switch off the fault message: Use the

I-On/0-Off

button to switch the washer

off.

Troubleshooting

Содержание NOVOTRONIC W 1612





























































Результаты поиска

Содержание NOVOTRONIC W 1612

Отзывы:

Похожие инструкции для NOVOTRONIC W 1612

Бренды по названию

Популярные бренды

Miele NOVOTRONIC W 1612, Руководство по эксплуатации

Результаты поиска

Содержание NOVOTRONIC W 1612

Отзывы:

Похожие инструкции для NOVOTRONIC W 1612

Бренды по названию

Популярные бренды