Miele NOVOTRONIC T 7644 C Скачать руководство пользователя

Страница: 51 / 56

Adjust keypad tone

An audible tone sounds every time a
button is pressed.

For programming and saving in
memory, follow steps

The programmable function is
programmed using the buttons.

Precondition:

– The dryer is switched off.

– The door is closed.

Press

Start/Stop

and keep it pressed

it during steps

Press the

I-On/0-Off

button in.

Wait until the

Start/Stop

button lights up

continuously . . .

. . . then release the

Start/Stop

button.

Press the

Gentle

button five times.

– The

Gentle

indicator light flashes

once slowly and once briefly.

–

and

flash alternatingly in the

display (default setting).

The number appearing alternatingly
with

means:

no Keypad tone

(default setting)

Keypad tone on

(

Express

indicator light also flashes)

Pressing the

Start/Stop

button

switches from one to the other.

Using the

I-On/0-Off

button, switch

the dryer off.

The programming is now stored in
memory. You can change it again at
any time.

Programmable functions

Содержание NOVOTRONIC T 7644 C

























































Результаты поиска

Содержание NOVOTRONIC T 7644 C

Отзывы:

Похожие инструкции для NOVOTRONIC T 7644 C

Бренды по названию

Популярные бренды

Miele NOVOTRONIC T 7644 C, Руководство по эксплуатации

Результаты поиска

Содержание NOVOTRONIC T 7644 C

Отзывы:

Похожие инструкции для NOVOTRONIC T 7644 C

Бренды по названию

Популярные бренды