Miele NOVOTRONIC T 7644 C Скачать руководство пользователя страница 10

Страница: 10 / 56

Control panel

Display

Delay

button

This button has a dual function:
- Selecting the duration of the

Timed cold

and

Timed warm

programs.

- Pre-selection of start time.

Buzzer

button

The end of the program is signaled
audibly.

Fault indicator / Optical interface

Description: See "Problem solving /
Customer service" section.

Start/Stop

button

Starts and stops a program.
Interrupts a program when pressed.
Flashes during program selection
and lights once the program starts.

Gentle

button

Delicate fabrics are dried at a lower
temperature.

Dryness

button

Indicator lights identify the drying
level selected.

Program

selector

Indicator lights identify the program
selected.

Door

button

This button opens the door
independently of the power supply.

I-On/0-Off

button

For switching the dryer on and off.

Operating the dryer

Содержание NOVOTRONIC T 7644 C

























































Результаты поиска

Содержание NOVOTRONIC T 7644 C

Отзывы:

Бренды по названию

Популярные бренды

Miele NOVOTRONIC T 7644 C, Руководство по эксплуатации

Результаты поиска

Содержание NOVOTRONIC T 7644 C

Отзывы:

Бренды по названию

Популярные бренды