Miele KM 6565 FR Скачать руководство пользователя страница 11

Страница: 11 / 12

11004250-02

Installation

*INSTALLATION*

Built-in circuit breakers



Circuit breakers at least type B or C:
Switch the lever from 1 (on) to 0 (off).

Residual current device (RCD)



Switch the main switch from 1 (on) to
0 (off) or press the test button.

Mains connection cable

The hob must be connected to the
electrical supply with a special
connection cable, type H 05 VV-F (PVC
insulated) with a suitable diameter.

Please see wiring diagram for
connection.

See the data plate on the hob for the
correct voltage and frequency.

Replacing the mains connection
cable



Risk of electric shock.

Incorrect connection to the power
supply may result in an electric
shock.
The mains cable must only be
replaced by a qualified electrician.

When replacing the mains cable only
use cable type H 05 VV-F with a
suitable cross section. A suitable
connection cable is available from your
Miele dealer.

Содержание KM 6565 FR













Результаты поиска

Содержание KM 6565 FR

Отзывы:

Похожие инструкции для KM 6565 FR

Бренды по названию

Популярные бренды

Miele KM 6565 FR, Руководство по установке

Результаты поиска

Содержание KM 6565 FR

Отзывы:

Похожие инструкции для KM 6565 FR

Бренды по названию

Популярные бренды