Miele G 811 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 60

background image

Checking the programmed water
hardness level

^

Turn off the dishwasher.

^

Turn the program selector to “Stop”.

^

Hold the “Top Solo” button in and at
the same time turn on the dish-
washer with the “On/Off” button. Re-
lease the “Top Solo” button within 2
seconds.

The “Salt” indicator will flash.

Note:

If any other indicators light or flash the
process must be repeated.

Exception:

If the “Rinse aid” indicator lights or
flashes, rinse aid was never added or
needs to be refilled.

^

Turn the program selector past
“Normal 55°C/ 130 °F” to “Energy
Saver”.

The “Top Solo” indicator lights. The
position of the program selector corre-
sponds to the water hardness level (see
table “Programming the water hardness
level”).

^

Turn the program selector to “Stop”.

^

Turn off the dishwasher.

Before using for the first time

16

«
...
14
15
16
17
18
...
»

Содержание G 811





























































Отзывы:

Нет отзывов

Похожие инструкции для G 811

Бренд: Washtech Страницы: 40

Бренд: Fagor Страницы: 148

Бренд: NEFF Страницы: 60

Бренд: Zanussi Electrolux Страницы: 16

Бренд: Dynex Страницы: 95

Бренд: Maytag Страницы: 52

HG6085D137609HW

Бренд: Hanseatic Страницы: 78

Бренд: Samsung Страницы: 22

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 88

WF-B105N(V/C/S)

Бренд: Samsung Страницы: 22

Бренд: Samsung Страницы: 16

WF702Y4BK Series

Бренд: Samsung Страницы: 704

Бренд: Samsung Страницы: 64

WF702U2BB Series

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 104

Бренд: Samsung Страницы: 1020

Бренд: Samsung Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды