Miele G 811 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 60

background image

Programming and setting the
water hardness level

Your water hardness must be pro-
grammed into the dishwasher using the
buttons on the control panel. The water
hardness selector in the wash cabinet
is then also set to correspond to the
water hardness level in your area.

Programming the water hardness
level

^

Turn off the dishwasher

^

Turn the program selector to “Stop”.

Hold the “Top Solo”-button in and and
at the same time turn on the dishwasher
with the “On/Off” button.Release the
“Top Solo” button within 2 seconds.

The “Salt” indicator flashes.

Note:

If any other indicators flash the process
must be repeated.

Except:

The “Rinse aid” indicator will light when
the reservoir is empty and needs to be
refilled.

^

Turn the water hardness level selec-
tor to the corresponding setting
(see table below).

gr/gal

ppm

Selector setting

1 - 5

20 - 90

Normal 55 °C/130 °F

6 - 8

110 - 140

Sani Wash

9 - 11

160 - 220

Normal 65 °C/150 °F

12 - 16

220 - 290

Light Wash 55 °C/130 °F

17 - 21

310 - 380

5 o’clock position

22 - 24

400 - 430

6 o’clock position

25 - 31

450- 560

7 o’clock position

32 - 70

580 -1260

Energy saver

The water hardness level is preset to
1 - 5 gr/gal (20 - 90 ppm).

Example:

If the water hardness level is
10 gr/gal select setting “Normal
65 °C/150 °F”.

Before using for the first time

14

«
...
12
13
14
15
16
...
»

Содержание G 811





























































Отзывы:

Нет отзывов

Похожие инструкции для G 811

Бренд: GE Страницы: 2

Бренд: Kleenmaid Страницы: 30

FAVORIT 64080 i

Бренд: AEG Electrolux Страницы: 44

Бренд: NEFF Страницы: 29

Бренд: Fisher & Paykel Страницы: 5

Бренд: Philco Страницы: 36

Бренд: VALBERG Страницы: 172

Бренд: Electrolux Страницы: 20

Бренд: Electrolux Страницы: 27

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 42

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 50

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды