background image

,

All electrical work must be

carried out by a suitably qualified
and competent person in
accordance with local and national
safety regulations.

^

Connection should be made via a
suitable isolator, with an on-off switch
which should be easily accessible for
servicing work.

^

For extra safety it is advisable to
install a residual current device
(RCD) with a trip current of 30 mA (in
accordance with DIN VDE 0664, VDE
0100 Section 739).

WARNING

THIS APPLIANCE

MUST BE EARTHED

^

Equipotential bonding should be
carried out.

^

The mains connection cable may
only be replaced by an original Miele
spare part or an apppropriate cable
with wire end ferrule.

^

For technical data see data plate or
wiring diagram supplied.

The machine must only be operated
with the voltage, frequency and fusing
shown on the data plate.

The machine is

not convertible

.

The

data plate showing relevant test

marks (VDE, DVGW etc.) is situated
on the right hand side panel at the
back.

The wiring diagram is secured to the
inner side of the service panel beneath
the tank.

Bonding connection

There is a screw connection point
marked with the earth symbol (

8

) in the

front of the sump area, to which the
earth lead must be connected.

There are further notes on electrical
connection in the Installation
diagrams supplied.

Electrical connection UK

46

Содержание G 8072





















































Отзывы: