Miele G 7960 C SCVi Скачать руководство пользователя страница 18

Страница: 18 / 124

Guide to the appliance

Display functions

The display is used to select or set the
following:

- The programme

- Options

- The timer

- The

Settings

The display can show the following:

- The programme name

- The programme stage

- The estimated time left for the

programme to run

- The energy and water consumption

(EcoFeedback)

- Any relevant fault messages and

information

To save energy, the dishwasher
switches off after a few minutes if you
do not press any sensor controls
during this time.
Touch the



sensor control to switch

the dishwasher back on.

The sensor controls on the control
panel and in the display react to
fingertip contact.

The touch display can be scratched
by pointed or sharp objects, e.g.
pens.
Only touch the display with your
fingers.

Touch the required menu option to
select it.

The currently selected setting is marked
in orange and can be changed.

The

sensor control in the display is

used to confirm a message or setting
and to move to another menu level.

To exit a sub-menu again, use the



Back sensor control.

Touch the



sensor control at any time

to return to the Programme menu.

If you do not press any sensor controls
for several seconds, the display will
revert to the previous menu. You will
then have to enter your settings again.

Содержание G 7960 C SCVi





























































































































Результаты поиска

Содержание G 7960 C SCVi

Отзывы:

Похожие инструкции для G 7960 C SCVi

Бренды по названию

Популярные бренды

Miele G 7960 C SCVi, Руководство по эксплуатации

Результаты поиска

Содержание G 7960 C SCVi

Отзывы:

Похожие инструкции для G 7960 C SCVi

Бренды по названию

Популярные бренды