background image

Service

112

Contact in the event of a fault

In the event of any faults which you
cannot remedy yourself, please contact
your Miele dealer or the Miele Customer
Service Department.

You can book a Miele Customer
Service Department call-out online at
www.miele.com/service.

Contact information for the Miele
Customer Service Department can be
found at the end of this document.

Please quote the model identifier and
serial number of your appliance (Fabr./
SN/Nr.) when contacting the Miele
Customer Service Department. This
information can be found on the data
plate.

Please note that telephone calls may be
monitored and recorded for training
purposes and that a call-out charge will
be applied to service visits where the
problem could have been resolved as
described in this booklet.

The data plate is located on the right
side of the door.

EPREL database

From 1 March 2021, information on
energy labelling and ecodesign
requirements will be available in the
European Product Database (EPREL).
You can find the product database at
the following link https://
eprel.ec.europa.eu/. Y
ou will be asked
to enter the model identifier.

The model identifier can be found on
the data plate.

AC xxxV xxHz

x,x kW
xx A

Made in xxx

X xxxx

Mat.: xxxxxxxx

Guarantee

For information on the appliance
guarantee specific to your country
please contact Miele. See end of this
booklet for contact details.

Содержание G 7960 C SCVi





























































































































Отзывы: