manualshive.com logo in svg

Miele G 5266, Руководство по эксплуатации, Страница: 77 / 92

Поделиться
Скачать
Miele G 5266 Скачать руководство пользователя страница 77

Frequently Asked Questions

77

Problem

Possible cause and solution

Plastic parts are
discoloured.

Natural dyes, e.g., from carrots, tomatoes, or
ketchup may be the cause. The amount of detergent
used or its bleaching effect was not sufficient to deal
with natural dyes.

Use more detergent (see “Detergent”). 
Parts that are already discoloured will not revert to
their original colour.

White residue is visible
on the dishware.
Clouding has occurred
on glassware and
cutlery. The film can be
wiped off.

The rinse aid dosage is set too low.

Increase the dosage (see “Rinse aid” under
“Before using for the first time”).

The salt reservoir is empty.

Fill the salt reservoir (see “Reactivation salt” under
“Before using for the first time”).

The salt reservoir cap has not been screwed on
correctly.

Replace it, making sure that it screws back on
correctly.

Unsuitable combination detergents were used.

Switch to another detergent. If using detergent
tabs or powder detergent, do not choose
combination products and ensure you refill the
reactivation salt and rinse aid.

The water softener is programmed to too low a water
hardness level.

Program the water softener to a higher water
hardness level (see “Water softener” under “Before
using for the first time”).

Содержание G 5266





























































































Отзывы:

Нет отзывов