manualshive.com logo in svg
background image

Electrical connection

32

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE

THE FOLLOWING:
All electrical work should be

performed by a qualified electrician

in strict accordance with national

regulations (for USA: ANSI-NFPA 70)

and local safety regulations.

Installation, repairs and other work

by unqualified persons could be

dangerous.
Ensure that power to the appliance is

OFF while installation or repair work

is performed.
Verify that the voltage, load and

circuit rating information found on

the data plate (located behind the

baffle filters), match the household

electrical supply before installing the

hood.
Use only with ventilation hood cord-

connection kits that have been

investigated and found acceptable

for use with this model hood.
If there is any question concerning

the electrical connection of this

appliance to your power supply,

please consult a licensed electrician

or call Miele’s Technical Service

Department.

WARNING: THIS APPLIANCE MUST

BE GROUNDED

The hood comes equipped with a

power cord with a NEMA 5-15 molded

plug for connection to a 120 VAC,

60 Hz, 15 A power outlet.

Grounding Instructions

WARNING - Improper grounding can

result in a risk of electric shock.

This appliance must be grounded. In

the event of an electrical short circuit,

grounding reduces the risk of electric

shock by providing a path of least

resistance. This appliance is equipped

with a cord having a grounding wire

with a grounding plug.
If there is any doubt, have the electrical

system of the house checked by a

qualified electrician.
Do not use an extension cord. If the

power supply cord is too short, have a

qualified electrician install an outlet

near the appliance.

The plug must be plugged into an

outlet that is properly installed and

grounded.

WARNING - Grounding instructions

(Canada)

The grounding-type attachment plug

shall be connected to a grounding-

type receptacle installed in

accordance with CSA C22.1-12,

Canadian Electrical Code, Part I.

Содержание DA 399-6
















Отзывы: