Miele CVA 5060 Скачать руководство пользователя страница 64

Страница: 64 / 80

. . . the machine does not switch on
even though the "Switch on at"
setting for the timer has been
activated.

The system lock has been activated.

Deactivate it. (See "Settings:
customising your machine - Safety
(Activating the System lock)").

The machine was not used after being
switched on automatically 3 times in
succession.

Switch the machine on and make a
drink.

. . . you cannot read the display.

If the machine is installed too low down,
the display can be hard to see.

Try to improve this by adjusting the
display contrast or brightness (see
"Settings: customising your machine -
Setting the display").

. . . milk froth or milk is not flowing
out of the central spout.

The spout is clogged up.

Clean the central spout - especially
the rubber stoppers - and the milk
pipework (see "Cleaning and care -
"Central spout" and "Milk pipework").

. . . a message appears in the display
reminding you to fill or replace the
milk flask even though it is full and
positioned correctly.

Clean the flask thoroughly, paying
particular attention to the area around
the handle and the neck (see
"Cleaning and care - Stainless steel
milk flask").
Any soiling in these areas can
prevent the sensors for the milk flask
from working properly.

. . . the coffee grinder makes a louder
noise than usual.

There may be stones in amongst the
coffee beans, or the bean container
may have emptied during grinding.

Switch the machine off immediately.

If the bean container is

not

empty

call the Miele Service Department. If
it is empty fill the container with fresh
beans.

. . . the espresso is dispensed too
quickly.

The coffee is too coarsely ground.

Set the grinder on a finer setting (see
"Setting the coffee grinder").

. . . the espresso is dispensed too
slowly.

The coffee is too finely ground.

Set the grinder on a coarser setting
(see "Setting the coffee grinder").

Problem solving guide

Содержание CVA 5060

















































































Результаты поиска

Содержание CVA 5060

Отзывы:

Бренды по названию

Популярные бренды

Miele CVA 5060, Руководство пользователя

Результаты поиска

Содержание CVA 5060

Отзывы:

Бренды по названию

Популярные бренды