Midea X1BP-09N8D0-O, Руководство пользователя

Страница: 59 / 64

ECO/GEAR function
Under cooling mode, press this button, the remote controller will adjust the temperature
automatically to 24 C/75 F, fan speed of Auto to save energy (only when the set temperature
is less than 24 C/75 F). If the set temperature is above 24 C/75 F, press the ECO button,
the fan speed will change to Auto, the set temperature will remain unchanged.
NOTE:
Pressing the ECO button, or modifying the mode or adjusting the set temperature to less
than 24 C/75 F will stop ECO operation.
Under ECO operation, the set tmeperature should be 24 C/75 F or above, it may result in
insufficient cooling. If you feel uncomfortable, just press the ECO button again to stop it.
O
O
O
O
O
O
O
O
O
O
Press X-ECO button to enter the energy efficient mode in a sequence of
following:
ECO GEAR(75%) GEAR(50%) Previous setting mode ECO......
Note:This function is only available under COOL mode
.
ECO operation:
GEAR operation:
Press the ECO/GEAR button to enter the GEAR operation as following:
75%(up to 75% electrial energy consumption)
50%(up to 50% electrial energy consumption)
Previous setting mode.
Under GEAR operation, the display on the remote controller will alternage between
electical energy consumption and set temperature.
FP function
LOCK function
O
O
O
O
Keep pressing Fan button for more than 2 seconds to activate/disable Silence
function(some units).
Due to low frequency operation of compressor, it may result in insufficient cooling
and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while
operating will cancel silence function.
Silence function
Clean
5s
5s
Boost
Press this button 2 times during one second under HEAT Mode and setting temperature of
16 C/60 F or 20 C/68 F(for model RG10A10(B2)/BGEF).
The unit will operate at high fan speed (while
compressor on) with temperature automatically
set to 8 C/46 F.
Press this button 2 times under HEAT Mode and setting temperature of 16 C/60 F to activate
the FP function. Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel
this function.
Note: This function is for heat pump air conditioner only.
2
+
Press together
Clean
button and
Boost
button at the
same time more than 5 seconds to activate Lock function.
All buttons will not response except pressing these two
buttons for two seconds again to disable locking.
2s
This feature avoids direct air flow blowing on the
body and makes you feel indulging in silky
coolness.
NTOE: This feature is available under cool,
Fan and Dry mode only.
FRESH function( ) (some units) :
Breeze Away function( ) (some units) :
Sleep function( ) :
AP function( )(some units) :
Follow me function( ):
SET function
or
SET
SET
OK
Press the SET button to enter the function setting, then press SET button or TEMP or TEMP
button to select the desired function. The selected symbol will flash on the display area, press the
OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET
button to scroll through operation functions as follows:
Breeze Away ( ) Fresh ( ) Sleep( ) Follow Me( ) AP mode( )
[ ]: If your remote controller has Breeze Away button or Fresh button, you can not use the SET
button to select the Breeze Away or Fresh feature.
J J J J
* *
*
The FOLLOW ME function enables the remote
control to measure the temperature at its
current location and send this signal to the
air conditioner every 3 minutes interval.
When using AUTO, COOL or HEAT modes,
measuring ambient temperature from the
remote control(instead of from the indoor
unit itself) will enable the air conditioner to
optimize the temperature around you and
ensure maximum comfort.
The SLEEP function is used to decrease
energy use while you sleep (and don t need
the same temperature settings to stay
comfortable). This function can only be
activated via remote control.
Note:
The SLEEP function is not available
in FAN or DRY mode.
,
For the detail, see sleep operation in
USER S MANUAL.
,
,,
,,
,,
,,
When the FRESH function is initiated, the
Ionizer/Plasma Dust Collector(depending
on models) is energized and will help to
remove pollen and impurities from the air.
,
,
,
,
,
,
,
,
If the memory feature is stopped,
OF
displays for 3 seconds on the screen.
While the memory feature is activated,
press the ON/OFF button, shift the mode
or power failure will not cancel the Follow
me function.
NOTE: Press and hold Boost button for
seven seconds to start/stop memory
feature of Follow Me function.
If the memory feature is activated,
On
displays for 3 seconds on the screen.
Choose AP mode to do wireless network
configuration. For some units, it doesn’t
work by pressing the SET button. To enter
the AP mode, continuously press the LED
button seven times in 10 seconds.
5 9