3
4
Function Buttons
ON/OFF
Button
SET Button
Button
Turns the unit on or off
FAN SPEED
FAN SPEED
Selects fan speeds in
the following order:
Selects fan speeds in
the following order:
AU%
AU%
g
g
g
g
100%
20%
60%
60%
80%
40%
40%
80%
20%.
100%.
g
g
g
g
g
g
Adjust
Adjust
Press the Adjust
or button to increase
/decrease the fan
speed in
1%
increments.
Press the Adjust
or button to increase
/decrease the fan
speed in
1%
increments.
ECO/GEAR Button
Starts and stops ECO
feature.
Press and hold down this
button for 2 seconds to
turn on the GEAR function.
Starts and stops the louver
movement.
Press this button, the horizon-
tal louver swing up and down
automatically. Hold down this
button for 2 seconds, the
vertical louver will swing left
and right automatically.
Scrolls through operation
functions as follows:
Turns indoor unit s LED
display and air conditioner
buzzer on and off, which
create a comfortable and
quiet environment. Under
this mode, the display will
illuminate for 10 seconds
while adjusting the mode, set
temperature or fan speed, etc.
MODE
Scrolls through operation
modes as follows:
Timer on( ) Timer off( )
Sleep( )
g
g
g
g
g
g
Turbo( )
Self Clean( )
Follow Me( )
Fresh( )
,
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the
How to Use The Basic/Advanced Functions
section of
this manual.
NOTE
：
Please do not select HEAT mode if the machine you purchased is cooling only
type. Heat mode is not supported by the cooling only appliance.
AUTO
g
COOL
g
DRY
g
HEAT
g
FAN
NOT SURE WHAT A FUNCTION DOES?
Refer to the
How to Use Basic Functions
and
How to Use Advanced Functions
sections of this manual for a detailed
description of how to use your air conditioner.
SPECIAL NOTE
Button designs on your unit may differ
slightly from the example shown.
If the indoor unit does not have a particular
function, pressing that function s button on
the remote control will have no effect.
TIPS FOR USING REMOTE CONTROL
The remote control must be used within 8
meters of the unit.
The unit will beep when remote signal is
received.
Curtains, other materials and direct
sunlight can interfere with the infrared
signal receiver.
Remove batteries if the remote control
will not be used more than 2 months.
Prevent any liquid from falling into the
remote controller.
If other electrical appliances react to the
remote controller, either move these
appliances or consult your local dealer.
INSERTING AND REPLACING BATTERIES
INSTALLING REMOTE CONTROL HOLDER
Your air conditioning unit comes with two
AAA batteries. Put the batteries in the
remote control before use:
1. Remove the back cover from the remote
control, exposing the battery compartment.
2. Insert the batteries, paying attention to
match up the (+) and (-) ends of the
batteries with the symbols inside the
battery compartment.
3. Install the back cover on.
The remote controller can be attached to a wall
or stand by using a remote controller holder.
Before installing the remote controller, check
that the air conditioner receives the signals
properly.
the remote controller on the holder.
1.
2. Install the holder with two screws, or just put
the holder on the desk.
3. Put
BATTERY NOTES
For optimum product performance:
Do not mix old and new batteries, or
batteries of different types.
Do not leave batteries in the remote control
if you don t plan on using the device for
more than 2 months.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted
municipal waste. Refer to local laws for
proper disposal of batteries.
,
,
Handling The Remote Controller
Remove the back cover
to install batteries
The selected symbol will flash
on the display area, press the
or button to confirm.
Increases temperature in
O
O
0.5 C(1 F) increments.
Hold down this button to
increase temperature in
O
O
1 C(1 F) increments. Max.
Temperature is
o
O
30 C(86 F).
Decreases temperature
O
O
in 0.5 C(1 F) increments.
Hold down this button to
decrease temperature
O
O
in 1 C(1 F) increments.
Min. temperature is
O
O
16 C(60 F).
Mode
SET
