3
3
4
4
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Read completely, then follow step by step.
Fig.1
E
F
D
2.3m or more
Air filter
12cm or more
12cm or mote
15cm or more
A
B
C
C
A
60cm
or m
ore
6
0
cm
o
r
m
o
re
30cm
or m
ore
Air Outlet
30cm
or m
ore
Wrapping tape(wrap the
insulation pipe with the tape
from bottom to top)
Allow two of A, B and C
directions to be free
from obstructions.
Where there is a danger of the
unit falling, use foot bolts to
fix.
B
200c
m or
mor
e
Additional drain pipe
Accessories
( C)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
SLEEP
ON/OFF
TIMER OFF
AIR
DIRECTION
RESET LOCK
SET TEMPERATURE
SWING
LED
DISPLAY
TURBO
There should not be any heat source, inflammable gas or stream near the unit.
There should not be any obstacles blocking the air circulation.
A place where air circulation in the room is good.
A place where drainage can be easily done.
A place where noise prevention is taken into consideration.
Do not install the unit near the door way.
Ensure the restrictions on installation specified in the indoor unit installation drawings are met.
Select a location which is firm enough for installation so that the device is not subjected to
vibrations.
The device should beinstalled at a distance of at least 1m from all other electrical devices and
installations, e.g. TV, radio,computer, etc.
There should not be any direct sunlight. If unavoidable, sunlight prevention should be taken
into consideration.
Indoor unit
Outdoor unit
If an awning is built over the unit to prevent direct sunsight or rain,be careful that heat
radiation from the condenser is not obstructed.
There should not be any animal or plant which could be affected by hot air discharged.
Make sure that there is sufficient space as specified in the installation drawings.
Do not place any obstacles which may cause a short circuit of the discharged air.
Select a location which avoids causing a nuisance to neighbours from noise and air emissions
from device.
Select a location which is sufficiently well ventilated.
Never cover the air inlets and outlets.
The location must be sufficiently firm for installation and the prevention of vibrations.
There must be no risk presented by combustible gas or gas escaping as a result of corrosion.
Avoid a location where there is a high salt content.
Avoid a location which is heavily exposed to dust.
Avoid a location to which the general public have access.
Selecting installation place
Installation plate
Seal
Drain joint
Ower s manual
Installation manual
Remote controller
illustration
Clip Anchor
Clip Anchor(5)
Mounting plate fixing
screw ST3.9x25
Installation plate fixing
screw ST3.9x25(5)
Remote controller
Remote
controller
Fixing screw for remote
controller holder
ST2.9X10
Fixing screw for
remote controller
holder ST2.9X10
Air freshening filter
(used to install on
Air filter)
1
(for cooling & heating
models only)
5
5
1
1
1
1
1
2
1
2
Use the supplied installation accessories as required. The items necessary to install
this air conditioner are not included must be purchased separately.
Remote controller holder
Dry battery AAA.LR03
Indoor unit
NOTE
:
optional
parts
Indoor & outdoor unit installation drawings
The mounting plate should be installed on a wall
which can support the weight of the indoor unit.
Before screwing the remote
controller holder to the wall,
make sure that control signals
are properly received by
indoor unit.
In sites with poor drainage, use
block bases for outdoor unit.
Adjust its height until the unit
is leveled. Otherwise, water
leakage or pooling of water
may occur.
A
I
J
K
L
M
B
C
D
E
F
G
H
H
1
,
Install the air freshening
filter at the back of air filter
NOTE:
Appearance of outdoor unit and indoor unit may differ from some models.
The actual shape shall prevail.
