background image

3

A. LOCATION AND FUNCTION OF

CONTROLS

This section provides a basic description of the Mighty Chef

oven’s controls, their location, and the functions they

perform.  The operator MUST be familiar with the controls.

See Figure 4.

1.

MenuSelect

® 

controller

Multi-function keypad which contains the following:
a.

The display 

shows the current preset menu

selection, temperatures, cook time, or error/service

information, depending on the mode of operation.

b.

The ready light 

illuminates when both heating

zones of the oven have reached their set

temperatures.

c.

The Top Temp key 

displays/sets the top zone

temperature.

d.

The Bottom Temp key 

displays/sets the bottom

zone temperature.

e.

The Cook Time key 

displays/sets the cook time.

f.

The Ref Temp key 

displays a reference

temperature for the top or bottom heating zone.

g.

The Sngl Pizza key 

adjusts the temperature of the

top heating zone to properly cook a single pizza,

or the last of a group of pizzas.

h.

The Prog key 

allows reprogramming of the five

Preset Menu Selections.

i.

The Prog Override key 

allows a Preset Menu

Program to be temporarily changed.

Figure 4 - Controls

3. Con-

veyor

reversing

switch

2. Power

On/Off (I/O)

switch

j.

The Up Arrow and Down Arrow keys 

are u

sed to edit

cook time and temperature settings.

k.

The Preset Menu keys (1-5) 

are used to select a

Preset Menu to change or operate.

2.

Power On/Off (I/O) switch

Switches the oven ON (“I”) and OFF (“O”).

3.

Conveyor reversing switch

Changes the direction of conveyor travel.

CAUTION

Do not operate the conveyor reversing switch while

the conveyor is in motion.

B. DAILY STARTUP PROCEDURE

1. Adjust the position of the draft curtains at the ends of

the cooking chamber (if necessary).  This procedure

is described in detail in Section F, 

Draft Curtain

Adjustment

, on Page 6.

IMPORTANT

When cooking at very high temperatures (either heating

zone is 400°F / 204°C or higher), the oven should be

pre-heated for at least 10 minutes WITH THE DRAFT

CURTAINS IN THE FULLY-LOWERED POSITION

and both heating zones set to 599°F / 315°C.  After

pre-heating, the curtains may be repositioned as

required.

2. Restore power to the oven at the circuit breaker/fused

disconnect.

3. Switch the Power On/Off (I/O) Switch to the ON (“I”)

position.

e

d

c

f

i

k

b

a

j

h

g

SECTION 3 - OPERATION

1. MenuSelect

® 

controller

Содержание CTX Mighty Chef TCO2114













Отзывы: