Middle Atlantic C3-SHELFKIT Скачать руководство пользователя страница 5

REQUIRED TOOLS

• Protective Eyewear

• Power Driver

• Rubber Mallet

• #2 Phillips 

 Screwdriver

• #2 Phillips Bit

WARNING

: Use tools with caution and follow all 

necessary safety protocols.

AVERTISSEMENT

: Utiliser des outils avec prudence 

et suivre tous les protocoles de sécurité nécessaires. 

INTRODUCTION

NOTE

:

• Only use this instruction sheet to install your C3 Series Slide-Out Rack option after you refer to the C3  

  Series Credenza Frame instruction sheet (100-00032) and secure the frame to your wall.

• If your installation includes a purchased fan kit and/or a large cover option (for your purchased display  

  option), after installing this and any other options you may have purchased for your credenza, refer to 

  the C3 Series WoodKit instruction sheet (100-00040) to install your woodkit, and then refer to the C3  

  Series Fan Kit (C3-FANKIT) instruction sheet (100-00039) and/or C3 Series Display Mount Large 

  Cover Option instruction sheet (100-00035) to install your fan kit and/or your large cover option,  

 

  respectively. Kits and options other than the fan kit and large cover option should be installed before  

  your woodkit is attached to the frame.

• This instruction sheet first covers installing the power strip mounting clips (into the same bay you're   

  installing the slide-out rack) and then covers installing the slide-out rack itself. The power strip should  

  only be installed into the clips after the woodkit is attached to the frame. For more information, refer to  

  "Installing Power Strip Into Mounting Clips" on page 10 of the C3 Series WoodKit instruction sheet    

 (100-00040).

• Instruction sheets may also be accessed at www.middleatlantic.com.

SUPPLIED COMPONENTS AND HARDWARE (CONTINUED)

NOTE

: You may have purchased a Lever Lock option (LLOCKSWRF-KIT) 

for your Slide-Out Rack Option (C3-TECHKIT4-SO).

LEVER LOCK™ OPTION (LLOCKSWRF-KIT)

(6x) 10-32 x ¾” 

Truss Screw With 

Washer

L

Lever Lock 

Adapter Brackets

K

(2x)

2” Lever Lock

Vertical Channel

M

10” Lever Lock 

Vertical Plate

N

(6x)

Securing Rivet

P

(20x) 

Washer

R

Face After Panel

S

Page 5

NOTE

• To order more hardware, contact support at [email protected] or (866) 977-3901.

• Additional hardware is included that may not be required for your installation.

Содержание C3-SHELFKIT













Отзывы: