manualshive.com logo in svg

Microtest PentaScanner, Руководство пользователя

Поделиться
Скачать
Microtest PentaScanner Скачать руководство пользователя страница 7

Page 7

Status

Slow Blink

Battery is low

Charging

Steady Light

The Injector is inactive, the AC adapter is present
and the battery pack is being charged at the maximum rate.

Charging

Off

The Injector is inactive and the battery or AC adapter is
not present; or the Injector is active.

Charging

Blinking (once

The Injector is inactive and the AC adapter is present; the 

every 10 

battery pack is fully charged and the Injector is in trickle 

seconds

charge mode.

Circuit

Blinking

Overvoltage condition

Guard,
Pass, Fail,
plus steady
tone

Super I/Super Injector LED Indicators

Indicator

State

Description

Status

Rapid blink

Test in progress

Status

Steady light

Injector waiting for

                                              signal from Scanner
Status

Slow blink

Injector battery low

Pass

Steady light

Test has passed

Fail

Steady light

Test has failed

Fail, plus

Steady light

Overvoltage steady

tone condition

When to Use the Injector

Some measurements require the use of the Injector at the far end of the cable. For other
measurements, the Injector can be connected but its use is optional. The Scanner automatically
detects the presence of and configures the Injector for the measurement to be performed. The
following table outlines when to use the Injector:

Test Connector
(36-pin on Super
I or Mod 8
on Super Injector)

Pass
Indicator

Fail
Indicator

Status
Indicator

Содержание PentaScanner






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды