manualshive.com logo in svg

Microtek MIL-800XL Plus, Руководство пользователя, Страница: 36 / 36

Поделиться
Скачать
Microtek MIL-800XL Plus Скачать руководство пользователя страница 36

36     MII-800XL Plus User's Manual

Specifications

Type

Desktop flatbed film digitizer

Image Sensor

CCD (Charge-Coupled Device)

Lamp Source

LED

Scanning Modes

Grayscale in a single scanning pass

16-bit grayscale (Approx. 65,536 shades of gray)

8-bit grayscale (Approx. 256 shades of gray)

Resolution

Optical: 3200 dpi (H) x 6400 dpi (V)

Dynamic Range

4.7 Dmax (Max.)

Scanning Area

Transparent: 12

"

 x 15.9

" 

 (305 mm x 404 mm)

Product Life Cycle

100,000 scans or 5 years

Interfaces

Hi-Speed USB (USB 2.0)

Dimensions (L x W x H)

24.7

"

 x 14.8

"

 x 7.1

"

(627.5 x 375.9 x 180.5 mm)

Weight

35.4 lbs (16.1 kg)

Voltage

AC 100V to 240V, 47-63 Hz, 1.5A Max.

Power Consumption

54.9 W (Max.)

Environment

Operating temperature: 50° to 104°F (10° to 40°C)

Relative humidity: 20% to 85%

Storage temperature: 14° to 140°F (-10° to 60°C)

Relative humidity: 20% to 95%

Important

Specifications, software bundles, and accessories are subject to change without

notice.  Not responsible for typographic errors.

Содержание MIL-800XL Plus





































Отзывы:

Нет отзывов