manualshive.com logo in svg

Microsoft Surface Hub 55 inch, Руководство по сборке и монтажу

Поделиться
Скачать
Microsoft Surface Hub 55 inch Скачать руководство пользователя страница 5

©2015 Microsoft. Microsoft, the Microsoft logo, and the Microsoft Surface Hub logo are trademarks of the Microsoft 
group of companies.  Microsoft Corporation One Microsoft Way Redmond, WA  98052-6399 USA  

 

This document outlines the steps for assembling the Surface Hub 55” and Surface Hub 84”  
rolling stand. These stands require two people to assemble. Before beginning, make sure you 
have all of the components in the parts list. 

IMPORTANT: Avoid damage to your device.

 The Surface Hub 55” is intended to be supported 

only by its bottom edge when not supported by the mounting system. Rest it only on its bottom 
edge, and support it to keep it vertical. The Surface Hub 84” is intended to be supported only by 
the lifting handles when not supported by the mounting system. Do not place either device on 
its face, back, top, or sides.  

Specifications 

Model 

Device 

weight 

Stand 

weight 

Handle 

weight 

Designated 

load capacity 

Surface Hub 55” 

110 lb. 

270 lb. 

NA 

380 lb. 

Surface Hub 84” 

260 lb. 

270 lb. 

30 lb. 

560 lb. 

 

Required tools (not included) 

#2 Phillips screwdriver 
5mm hex key (55” only) 
6mm hex key (84” only) 
13mm wrench 

 

 

 

Содержание Surface Hub 55 inch















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды