MicronWings MINIMUM RC J3 CUB Скачать руководство пользователя страница 8

 

While the airframe and wheels are drying, it’s a good 

chance to connect up all your electronics and check 
everything works properly.  
 
Check all your trims and mixing on your transmitter 
are set these to neutral. 
 
 

 

 

If using the recommended receiver, connect the red 
and black battery wires as shown here. For the 
motor, note that the white wire is towards the inside 
and the black wire on the outside. 

But don’t solder 

the motor wires as yet. 
 

 

Tape the horizontal stabilizer and elevator to a flat 
surface with modelling tape to leave 0.5mm gap 
between them. Then, use Blenderm hinge tape on 
either side to attach the elevator surface.  

Glue the horizontal stabilizer in 
place and check it is level.  
Allow to dry. 

 
Use a 0.5mm diameter micro drill bit to drill out the 
holes in the wheels so they spin freely on the 
undercarriage.  
 
Attach the wheels and use 4mm piece of the smaller 
heat shrink tube (0.6mm tube) to keep the wheel in 
place. Heat the heat shrink with a soldering iron tip 
to shrink it. 
 
Tape the vertical stabilizer in place with modelling 
tape as shown here. Leave a gap of 0.5mm at the 
back and 1mm at the top 
 

Also attach the vertical 
stabilizer control surface 
here with a thin piece of 
Blenderm hinge tape. 

0.5mm 

1mm 

Содержание MINIMUM RC J3 CUB















Отзывы: