manualshive.com logo in svg

Micron MC-20, Руководство пользователя, Страница: 25 / 37

Поделиться
Скачать
Micron MC-20 Скачать руководство пользователя страница 25

MC-20

User Manual / 

Air Pressure Setting

25/3

7

TWO WAYS TO SET PISTON PRESSURE: 

The machine has two ways to set the 

piston pressure. They are stroke setting and air pressure setting.

AIR PRESSURE SETTING: 

In the back of the MC-20 on the right hand side you will 

find the air pressure gage. The red numbers from 2 through 10 indicate the “BAR” 
reading. The blue numbers from 0 through 150 indicate the “PSI” reading.

The lager blue knob on top of the air pressure gage is used to adjust the air 
pressure. It is very important to follow these simple directions to prevent damage to 
the air pressure knob while adjusting the air pressure of the MC-20.

1. Lift the knob up

2. Turn the knob clockwise to increase the air pressure

3. Turn the knob counterclockwise to lower the air pressure

4. When desired air pressure is achieved, press the knob down to lock the

pressure setting

CAUTION:

 IF YOU DO NOT LIFT THE KNOB UP BEFORE YOU TURN IT TO SET 

THE AIR PRESSURE, YOU MAY DAMAGE THE KNOB AND CAUSE AN AIR 
LEAK. IF YOU DO NOT PRESS THE KNOB DOWN AFTER SETTING THE 
DESIRED AIR PRESSURE, YOU WILL FAIL TO LOCK THE SETTING IN PLACE.

FINDING THE PROPER PISTON PRESSURE SETTINGS: 

 IT IS A GOOD IDEA TO 

EXPERIMENT ON SMALL PIECES OF TEST MATERIAL TO FIND THE PROPER 
PISTON PRESSURE SETTINGS BEFORE STARTING ON A NEW JOB.

Содержание MC-20






































Отзывы:

Нет отзывов