If you have any difficulty with this Alarm System, please check the following before telephoning the Helpline.
P
PR
RO
OB
BLLEEM
M
SSO
OLLU
UTTIIO
ON
N
When finishing programming and pressing P
P0
0EE internal
alarm sounds.
Alarm activates on entry giving no time to switch off.
Unable to set system. Zone LED illuminated.
Panel showing fault. LED on.
• Tamper spring on panel not depressed.
• Bad connections at terminal block.
• Tighten wall screw and refit.
• Check terminal block connections.
• Zone 3 or 4 PIR can detect you on entry, or you have an
intruder.
• Move PIR if possible. Deal with problem.
• Door open or PIR is getting tripped by someone
moving.
• Close doors and keep still while entering password.
• Door contacts not close enough – 5mm.
• Move contact magnet closer.
TROUBLESHOOTING
P
PO
OSSSSIIB
BLLEE C
CA
AU
USSEE
**P
PLLEEA
ASSEE N
NO
OTTEE:: TTo
o m
ma
aiin
ntta
aiin
n o
op
pttiim
mu
um
m sse
eccu
urriittyy,, tth
he
e b
ba
atttte
erryy ssh
ho
ou
ulld
d b
be
e cch
he
ecckke
ed
d rre
eg
gu
ulla
arrllyy a
an
nd
d rre
en
ne
ew
we
ed
d e
evve
erryy yye
ea
arr..
M
Miiccrro
om
ma
arrkk
D
De
evvo
on
nssh
hiirre
e H
Ho
ou
usse
e,, 5
55
50
0 W
Wh
hiitte
e H
Ha
arrtt LLa
an
ne
e,, LLo
on
nd
do
on
n N
N1177 77R
RQ
Q
Micromark continuously tries to improve its products for the benefit of its customers. For this reason we reserve the right to make changes to any product at any time, without notice.
MICROMARK INSTRUCTIONS MMMM25153/171103
© Micromark 2003
System will not arm.
• Red STATUS LED is on continually.
• Check anti-tamper spring is fully depressed.
• Check Red and Yellow connections at siren terminals.
N
NO
OTTEESS:: On power up the panel may bleep. Press any button to stop bleep and continue installation.
The system has a non-volatile memory so will retain the programmed settings if the power adpator and battery are disconnected.
SSh
ho
ou
ulld
d yyo
ou
u e
exxp
pe
erriie
en
ncce
e d
diiffffiiccu
ullttiie
ess tth
he
en
n p
plle
ea
asse
e tte
elle
ep
ph
ho
on
ne
e tth
he
e H
He
ellp
plliin
ne
e o
on
n 0
08
8770
0 2
24
411 3
30
02
29
9
PART GUARD
Part Guard enables you to fully arm the system but to
leave zone 3 unarmed. This is useful for instance if you
arm the downstairs zones but need the upstairs
unarmed.
Press EE 0
0 P
P
EEn
ntte
err iin
n yyo
ou
urr p
pa
assssw
wo
orrd
d (e.g. 1122) plus E.
A continuous tone will sound from the control panel followed
by 2 bleeps.
Zone 3 will be inactive but the other zones will be armed.
To completely disarm, e
en
ntte
err yyo
ou
urr p
pa
assssw
wo
orrd
d.
2
??
??
??
??
EE
1
www.ukpanels.com
