background image

7

allow the water to run for a few minutes to
flush any debris caused by the installation.

•Close the faucet and check the Feed Water

Saddle Valve for leaks.

C. Drain Clamp Installation

Choose the drain outlet location per Sec. III, C.5,
page 5.

The following are instructions for discharging into
the sink drain pipe. (Refer to Fig. 1, page 1.)

1. Position the Drain Clamp on the sink drain

pipe above the drain trap. Allow room for
drilling. Tighten securely.

2. Use a battery powered or properly grounded

drill. Using the Clamp port as a drill guide,
drill a 

7

/

32

" hole through the wall of the drain

pipe. Do NOT penetrate the opposite side of
the pipe.

3. Locate the 

3

/

8

" Black Drain Tubing which is

shipped loose in the box.

NOTE: When cutting the polytubing make
clean, square cuts, failing to do so could result
in poor connections and possible leaks.

CAUTION: The lowest point of the line
should be the point of connection to the Drain
Clamp. There should be no sag in the line as

3/8" DRAIN CLAMP ASSEMBLY

Figure 4

Drain Pipe

1/4" Screw

Drain Clamp

Front Plate

Insert

Compression

Nut

 Black Drain

Tubing

1/4" Nut

Drain Clamp
Back Plate

•Assemble and tighten the brass screw.

•To pierce the tubing, turn the Valve Handle

fully clockwise (inward). A small amount of
water may escape from the outlet until it is
fully pierced.

•When you feel the Valve Handle firmly

seated in the clockwise direction, the copper
tube is pierced and the valve is closed.

2b. To install on (hard) Steel or Brass Tubing

supply line.

•The supply line should now be drained. Use a

battery powered or properly grounded drill to
avoid shock hazard.

•Drill a 

3

/

16

" hole in the supply line; (do not

drill through the opposite wall).

•Turn the handle to expose the lance no more

than 

3

/

16

" beyond the rubber gasket.

•Place the body of the valve over the hole so

that the lance fits into the hole.

•Assemble and tighten the brass screw.

•Turn the Valve Handle clockwise (inward)

until firmly seated. The valve is closed.

3. With the Feed Water Saddle Valve closed,

open the sink faucet and the water supply and

Содержание T.F.C.-25D





















Отзывы: