Out power power, RMS
10 Watt RMS
Power distribution, Watt
2.5 Watt x 2 + 5 Watt
Harmonic distortion
< 0.5% 1 W 1 kHz
Frequency response
50 Hz - 20 kHz
Signal/Noise ratio, dB
> 70 dB
Separation, dB
> 44 dB
Tweeter driver type
2.5” x 2
Woofer driver type
6.5”
Input
3.5 mm stereo jack
Output
2RCA jacks, 3.5 mm stereo (Headphones)
Amplifier
Speaker
Interface
Mp3 \ Mp4
Media player
TV
PC or Notebook
Media
player
CD\ VCD \ DVD
Blu-Ray player
Connections
Operations
EN
5
EN
6
To any media player, CD/DVD player,
Mp3/Mp4 or TV with 3.5mm stereo jack
Operation:
1. Plug the AC power plug to the wall AC source or any AC power distribution sockets.
2. Ensure the volume level is lowered to minimum.
3. Start the media player and its playback audio.
4. Slowly increase the volume level to your preferred level.
5. Press “Input mode” knob to switch between Bluetooth and AUX modes.
6.
Stand-by
Long press the
Knob 2 seconds or no receiving signal within 15 mins, turn into standby
mode and LED illuminates red. Adjust the Volume Knob to enter working state.
Note: Never listen to loud music for prolong period as it might affect your hearings.
Installation:
Precaution: Prior to connecting the speakers, ensure the AC power plug is removed from the AC source.
Secondly, ensure the volume knob is set to zero.
1. First connect the left and right satellite speakers, then connect the right satellite to the subwoofer.
2. Place both satellites on extreme sides of the listening position.
3. Place the subwoofer on the floor and with its back near the wall for more bass.
4. Next, connect the playback source to the 3.5mm audio input jack.
5. Last, connect the AC power cord to the AC power supply source. Please always ensure the AC power
ratings printed on the rear panel of the satellite match with your country's AC power supply ratings. If
they do not match, please do not connect the power. This will damage the speaker system.
Technical Information
Question
Solution
Power LED won’t light up
No sound
One or more satellite no sound
Static sound heard when volume
knob is turned
What are the products
supported?
Sound is distorted
If the problem still exists, please contact the distributor or ask for professional service
Check if the system is powered on
Check the power plug is well connected
Check if the audio source is working well
Check if the audio and speaker cables are connected
Check if the volume is at the right level
Check if the satellite cable is well connected, and ensure source
connection is correctly inserted
Turn off the playback source first, then turn the speaker volume
knob several times. Playback again and monitor. The static noise
is due to dust, so simply turning the volume will remove it easily.
Any plackback devices such as PC, notebook, CD/DVD player,
Media players with 3.5 mm stereo plug
Check if the source file is not corrupted, play a different song and
test
- the end -
Power supply
Wireless (Bluetooth®)
1. Please turn on the speaker system. The LED blinks blue and the speaker emits a tone. It
will default to Bluetooth pairing mode .
2. Turn on Bluetooth function on your device, search and select "Virtuoso" in the Bluetooth device list.
3. Play music from Bluetooth enabled devices.
AUX Mode
1. Plug in Vitruoso speaker and it turns on, default to Bluetooth mode. LED illumicates bluet with a prompt tone.
2. Short press the Volume Knob into AUX Mode, LED illuminates purple with a prompt tone.
3. Play music from Bluetooth enabled devices.
Factory Reset
: Long press Volume Knob 5 seconds .
AC
IN
:
100 240V
-
~
50/60Hz
400mA
Troubleshooting
80-M115-97-0001(US)-01 2017-11-6
