background image

7 of 7 

 

PRX4SERL Four-Zone Receiver Decoder 

 

Specification 

 

Power Input:    

 

 

 

 

12V to 13.8V dc max @ 0.5A 

 

Power Consumption 

Standby (relays off, no serial port)  

 

 

28mA 

 

Standby (relays off, serial port connected)  

 

38mA 

 
Active 

serial 

decoder 

 

    63mA 

 
Active 

all 

relays 

     250mA 

 

Signal Format   

 

 

 

 

POCSAG FSK NRZ (Normal or Inverted) 

 

Frequency (fixed crystal)  

 

 

 

In the range 440 –470MHz 

 
Frequency 

Stability 

 

    +/- 

10ppm 

 

Channel 

Spacing 

 

    12.5 

or 

25KHz 

 

Frequency 

Deviation 

 

    +/- 

4.5KHz 

 
Over Air Baud Rate (fixed programmable)  

 

512 or 1200 bps 

 
Sensitivity 

 

     Maximum 

512bps 

 

      

V/m 

1200bps 

      7.

V/m 

 
Selectivity 

 

     >52dB 

 

Image 

Rejection 

     >52dB 

 

Spurious 

Rejection 

 

    >60dB 

 
Intermodulation 

 

    >52dB 

 
Relay Contact max rating  

 

 

 

0.5A @ 125V ac, 1A @ 60V dc 

 

Serial 

Port 

 

     RS232 

 

Serial 

Configuration 

 

    N, 

8, 

 
Serial Port baud rate    

 

 

 

9600 

 
 

 

 
 
 
 
 
 

Содержание PRX4SERL









Отзывы: