manualshive.com logo in svg

Microchip Technology KSZ8061MNX, Руководство пользователя

Поделиться
Скачать
Microchip Technology KSZ8061MNX Скачать руководство пользователя страница 16

KSZ8061MNX Evaluation Board User’s Guide

DS50002449A-page 16

 2016 Microchip Technology Inc.

2.3

CONFIGURATION INSTRUCTIONS

These instructions detail how to change between configurations. 

Figure 2-4

 and 

Figure 2-5

 show the location of the components referenced in the instructions.

1.

Two-PHY MII Back-to-Back Configuration. This is the default configuration, so 
these steps are only necessary if switching the board back from another 
configuration.

a) Place the KSZ8061 in MII Back-to-Back mode: install R40 and R41. Remove 

R39.

b) Connect the MII interfaces of the KSZ8061 and KSZ8081: install R212-R216 

and R222-226. Note that the MII clocks should not be connected between 
the two devices, so do not install R211 and R221.

c)

Both PHYs must be clocked from U3. Do not use crystal Y1, by removing 
either Y1 or R91 and R92.

d) Remove R1-R6.

e) Power the KSZ8081: install jumper JP1.

f)

Optionally, for optimal signal integrity, remove R11-R16 and R21-R26. 

2.

MII Loopback Configuration

a) Place the KSZ8061 in MII Back-to-Back mode: install R40 and R41. Remove 

R39.

b) Install R1-R6.

c)

Remove the KSZ8081 from the MII bus. There are three possible ways to do 
this:

- Remove jumper JP1 to remove power from the KSZ8081.

- Remove R211-R216 and R221-R226.

- Put the KSZ8081 in Isolate mode: install R70.

d) The KSZ061 may be clocked by either the external clock (U3) or the crystal 

(Y1). When changing between clock sources, the KSZ8061 does not require 
any setting changes.

e) Optionally, for optimal signal integrity, remove R11-R16 and R21-R26. 

3.

MII Connector Configuration

a) Place the KSZ8061 in Normal mode: remove R39 and R41. Install R40 if 

Auto-MDI/MDI-X is desired. Otherwise, remove R40.

b) Install R11-R16 and R21-R26.

c)

Remove R1-R6.

d) Remove the KSZ8081 from the MII bus. There are three possible ways to do 

this:

- Remove jumper JP1 to remove power from the KSZ8081.

- Remove R211-R216 and R221-R226

- Put the KSZ8081 in Isolate mode: install R70.

e) The KSZ061 may be clocked by either the external clock (U3) or the crystal 

(Y1). When changing between clock sources, the KSZ8061 does not require 
any setting changes.

f)

Connect the KSZ8061 evaluation board to a compatible connector on a 
Microchip switch evaluation board, and ensure that the port on the switch 
board is configured for MAC interface.

Содержание KSZ8061MNX



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды