Microchip Technology KSZ8061MNX Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 34

Microchip Technology KSZ8061MNX Скачать руководство пользователя страница 13

KSZ8061MNX EVALUATION

BOARD USER’S GUIDE



2016 Microchip Technology Inc.

DS50002449A-page 13

Chapter 2. Configuration

2.1

INTRODUCTION

This chapter discusses the configuration of the KSZ8061MNX Evaluation Board.

Items discussed in this chapter include:

•

Configuration Options

•

Configuration Instructions

•

•

•

Line Interface Connector Options

•

•

MII Management Interface (MDIO/MDC)

•

10-Pin Header (J7)

•

Status Indicator LEDs

•

•

•

KSZ8061MNX Strapping Options

•

MDIO/MDC Software Utility and FTDI Cable

2.2

CONFIGURATION OPTIONS

The KSZ8061 line interface is designed to permit the installation of any one of three
different connectors. These are described further in a later section.

The KSZ8061 MII data path can be configured in three different ways. Below are
descriptions and photographs of the configuration options.

1.

Two-PHY MII Back-to-Back
The evaluation board has two PHYs: a KSZ8061 (U1) and a KSZ8081 (U2). The
KSZ8081 is an ordinary 10/100 Ethernet PHY, and is on this board to support the
KSZ8061. Their MII buses can be connected together, which allows Ethernet
frames to be passed between the KSZ8061 line interface (J1, J2 or J3) and the
KSZ8081 line interface (J6). Unless otherwise indicated, this is the default board
configuration.

2.

MII Loopback
In this configuration, the KSZ8061 receives Ethernet traffic from the line inter-
face. At the MII interface, RX traffic is looped back the TX MII interface, and the
KSZ8061 transmits it back to the line interface. The KSZ8081 PHY is not used.
Do not reference

for resistor settings.

3.

MII Connector

The MII edge connector (J5) allows the KSZ8061MNX Evaluation Board to be
connected to the MAC port of a Microchip switch evaluation board, or to any
other device with an Ethernet MAC interface. Full duplex traffic can pass
between the MII connector and the KSZ8061 line interface (J1, J2 or J3). The
KSZ8081 PHY is not used.

«
...
11
12
13
14
15
...
»

Содержание KSZ8061MNX



































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды