Micro Technic Micronix 1800 Series Скачать руководство пользователя страница 19

Страница: 19 / 21

Users Manual & Installation Guide

PV- 1800:

Power supply module with GSM MODEM

Page 19 / 21

Max input voltage

30V, current limiting resistor = 3.32kohm / 250mW

Counter input

DI0 can act as a 16-bit up-counter by counting positive or

negative edges (configurable)

DI0 and DI1 can act as a 16-bit quadrature counter.

Max counting rate

10kHz

Connector type

10 pin box header

Digital outputs:

Number of channels

7 isolated PNP outputs

Max load current

0.5Adc, load current external delivered,

total current must not exceed 1.5Adc.

Max voltage

30Vdc

Protection

Snubber diode at each output

Connector type

10 pin box header

Environmental specifications:

Operating temperature:

-20º to +70ºC

Storage temperature:

-40º to 85ºC

Humidity:

20 to 90% non-condensing

Cyclic humidity:

ETS 300 019-2-5 or equal

Vibration:

10-1000 Hz Sinus and random @ 1-1,5G RMS

Sustained vibration:

EN 60068-2-34 & EN 60068-2-36

Shock

IEC 60068-2-27 & IEC 60068-2–29

Size (W x L x H)

90 x 96 x 14 mm – see next page

Weight:

116 g (excl. packaging)

*for details refer to SonyEricsson’s documentation:

•

GM47_48 Guidelines and

•

GM47_48 Integrators Manual

Содержание Micronix 1800 Series






















Результаты поиска

Содержание Micronix 1800 Series

Отзывы:

Похожие инструкции для Micronix 1800 Series

Бренды по названию

Популярные бренды

Micro Technic Micronix 1800 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Micronix 1800 Series

Отзывы:

Похожие инструкции для Micronix 1800 Series

Бренды по названию

Популярные бренды